Sean M

Members
  • Content count

    9
  • Joined

  • Last visited


Community Reputation

0 Neutral

About Sean M

  • Rank
    Full Member

Sean M's Activity

  1. Sean M added a post in a topic Calling 1JZ wiring gurus!   

    It sure was! Bad fuel pressure regulator! ISR replaced it and now its running. not good but its alive! It dies and doesnt freely rev, i think its due to bad tps.
    • 0
  2. Sean M added a post in a topic Calling 1JZ wiring gurus!   

    So i hooked up a noid light and i have injector pulse, i have spark and air. It runs on starting fluid. What could be my issue?
     
    • 0
  3. Sean M added a topic in Tech Chat   

    Calling 1JZ wiring gurus!
    Hi there, I have swapped a non vvti 1jz into an s13 hatch. I have done everything. Now it wont start. It cranks and has spark. It will sputter and jump around but if you call it 'running' it last for like 0.5 seconds. I have a brand new igniter and i have all sensors, map and tps and o2. Everything is powered on the ecu (ie. +B, +B1, IGSW, BATT) I have nsw grounded and sta to 12v when cranking. The injectors are powered via the 2 thick black w/orange striped wires. I have 12 on both sides of the injector clip which doesnt seem right to me, as now its backfeeding 12v into ecu at #10, #20, #30. I have the 4 row ecu. if anyone has an ecu i can use to test in Fraser Valley i can pay to get it out here. All comments are welcome. This car is so close to starting its going to be something dumb. I just want to find it at this point. 
    Thanks in advance. 
    • 3 replies
    • 150 views
  4. Sean M added a post in a topic 1jz s13 Build. First car, first project!   

    Hi all. Swap is complete! just literally fighting with wiring i think. Im posting into other threads atm.
    • 0
  5. Sean M added a topic in General Discussion   

    S13 Wheel Bearing HELP
    So ive found that t
    he s13 (89) has a difficult time getting front wheel bearings. Is there anywhere online you guys know of that are cheaper than like 90 bucks at lordco? I have access to a press.
    • 1 reply
    • 158 views
  6. Sean M added a topic in Parts For Sale/Wanted   

    S13 Struts with Eibach Springs.
    I have a set of struts with Eibach springs i could trade or cash or both. 
    • 0 replies
    • 128 views
  7. Sean M added a topic in Parts For Sale/Wanted   

    WTB S13 clutch pedal.
    Looking for a s13 (or s14) clutch pedal in the valley. I have a set of struts with Eibach springs i could trade or cash.
    • 0 replies
    • 116 views
  8. Sean M added a post in a topic 1jz s13 Build. First car, first project!   

    Just an update, saving up money and im getting the engine fully built at a shop this month. Then im sourcing all the parts. If anybody has any jz parts for sale message me.
    • 0
  9. Sean M added a topic in Introductions   

    1jz s13 Build. First car, first project!
    Hello all, picked up an 89 hatch from surrey for cheap, planning on dohc swapping it, but i found a good price on a non vvti 1jz and r154. It came with lots of parts. From what i understand i still need clutch, flywheel, bellhousing, shifter extension (buying mounts first), short shifter, driveshaft and wiring. I heard that independant speed shop in langley would be a good place to look into wiring. Im not sure about wiring specialties considering i have the full soarer harness. I need the sgi-5/7 units i think, please correct me if im wrong. If anybody has input and/or parts fs let me know, i hope to build it to just run stock for the close future. Ill upload some pictures within the week.  
    Toyota>Nissan, but why not both?
    • 10 replies
    • 905 views